Search
Search

banner

/
/
/
1.54 inch Programmable E Ink module, Touch Screen, Front-light Driver Shield, DESPI-K154D67
1/1
Number of views:
1000

1.54 inch Programmable E Ink module, Touch Screen, Front-light Driver Shield, DESPI-K154D67

This is a 1.54 inch e-ink screen module 200x200 resolution, and the e-paper display module supports Arduino, Raspberry Pi, STM32 Platform.
Number of views:
1000
Product serial number
620154D6
Category
EOL epd
Quantity
-
+
Overview
Specification
Download

1.54 INCH E-PAPER MODULE

ePaper 1.54 Shield, Built-in SD card, Touch Screen and Front-light Driver Shield.

INTRODUCTION

It can boost the driving voltage of Good Display's 1.54 inch e-paper display. Your image holds indemfinitely without power – put up your image, then shut down the power. Once these e-paper modules are updated they don't require any power and can actually be disconnected entirely and the content will remain on the display indefinitely. 

Also it preserves interfaces for 6 Pin touch panel and 6 Pin front light, which users can test. And this module board contains a Flash chip W25Q128 which is a serial NOR Flash memory with capacity of 128M-bit(16M-byte), making it easier for users to store pictures, libraries and other related data. And SD card slot is also reserved in the module, which users can choose to add an extra micro SD card. Therefore, Flash chip and SD card slot address the user need for more storage.

Related datasheet are under the Datasheets & Files section.

We also have other 24 Pin 1.54 e-paper display modules, if you have any needs, please contact us. 

 

FEATURE


●  SPI interface. It can be used on Raspberry Pi/Raspberry Pi Pico/ Arduino/ EPS8266/ ESP32/ STM32 Platform. We could provide the driving board, if you need, contact us please.

●   It integrated Flash chip and SD card slots for expanded development

●   Help users to learn how to drive the EPD with 6 PIN touch panel and 6 PIN front light

●   It has 3 LED lights, each LED light can be directly controled by the expansion pins. (Please refer to the PIN description.)

 

ePaper module instructions:

1. SPI interface. Compatible with Raspberry Pi/Raspberry Pi Pico/Arduino/ESP8266/ESP32/STM32 platforms.

We can provide a driver board upon request. Taking STM32 platform as an example, installation is as follows:

 

        

2. Integrate Flash chip and SD card slot for expansion development.

3. Assist users in learning how to drive touch screens and front-facing E Ink screens.

4. Incorporate 3 LED lights, each of which can be directly controlled via expansion pins. (Please refer to the pin description for pin definitions.)

PINS FOR EPD MODULE


1. Pins for EPD

1) BUSY: BUSY signal of e-paper. When the e-paper is refreshing, the BUSY pin sends out "busy" signal to MCU, the MCU can not read and write the e-paper IC; When the e-paper refresh is completed, the BUSY pin sends out "free" signal, the MCU can read and write the e-paper IC. GDEW series e-paper busy state is high level (GDEH series is low level), and free state is opposite.

2) RES: Reset signal of e-paper. Low level effective.

3) D/C: Data/ Command selection. High level for data, low level for command.

4) CS: Chip selection. Low level effective.

5) SCK: SPI serial communication clock signal line.

6) SDI: SPI serial communication data signal line.

7) GND: Negative power supply.

8) 3.3V: Positive power supply

 

2. Expanded Pins

1)  SI: Master Output Slave Input for SPI: INT pin for TP.

2)  SO: Master Input Slave Output for SPI: RST pin for TP.

3)  SCK: Clock signal line for SPI: SCL pin for TP.

4)  CS0: Chip selection for Flash: SDA pin for TP.

5)  CS1: Chip selection for SD.

6)  LED1: Control pin for LED1.

7)  LED2: Control pin for LED2.

8)  LED3: Control pin for LED3.

 

 

We could not find any corresponding parameters, please add them to the properties table

 

PARAMETERS

PART NUMBER

DESPI-K154D67

PLATFORM

STM32、Arduino、ESP32、ESP8266、Raspberry Pi、Raspberry Pi Pico

OUTSIDE DIMENSION(mm)

41.8x37.32

IC

SSD1681

RESOLUTION

200x200

POWER INTERFACE

3.3V

ACTIVE SIZE(mm)

27x27

OPERATING TEMP.

0℃~50℃

MAIN FUNCTION

Provide driving voltage for e-paper, touch panel and front light panel;
Help users operate e-paper quickly.

ADDITIONAL FUNCTION

Flash;

Micro SD;

LED;

MAX GRAYSCALE

4

COLOR

Black,White

INTERFACE

SPI

FULL REFRESH(s)

2

PARTIAL REFRESH TIME(s)

0.26

 

 

 

DRAWING

 

Related information download

Categories:
ePaper Shield
File size:
687KB
Number of downloads:
92
2021-07-30 14:54:38
Categories:
ePaper Shield
File size:
24KB
Number of downloads:
28
2021-07-29 16:15:35
Categories:
ePaper Shield
File size:
69KB
Number of downloads:
87
2021-07-29 16:15:07
Categories:
IC Datasheets
File size:
1.8M
Number of downloads:
571
2020-12-23 16:24:00
File size:
10.9M
Number of downloads:
1177
2021-04-19 13:56:00
File size:
1.1M
Number of downloads:
183
2021-04-15 10:05:14
Categories:
Example Code
File size:
1.9M
Number of downloads:
253
2023-05-22 14:17:00
Categories:
Example Code
File size:
14KB
Number of downloads:
249
2023-06-21 16:02:00
Categories:
Example Code
File size:
14KB
Number of downloads:
31
2021-04-15 10:03:00
Categories:
Example Code
File size:
14KB
Number of downloads:
349
2021-04-15 10:02:00
File size:
7KB
Number of downloads:
141
2021-05-20 13:40:41
Page up
1

Related Products

Previous page
1

Relevant information

Previous page
1

Leave us a message

产品中留言表单

Message

Message

Contact information

Contact information

We will contact you within one working day. Please pay attention to your email.

logo

Time of issue:2020-04-27 00:00:00

 

Buy E Ink Display

E Ink Display Solution

Industrial Displays

mmWave Radar Sensors 

Catalog

 

 

Contact

Time of issue:2020-04-27 00:00:00
Powerby:300.cn DaLian

copyright

Time of issue:2020-04-27 00:00:00

©2007-2025    DALIAN GOOD DISPLAY CO., LTD.   Privacy Policy      All Rights Reserved.      ICP08000578-1

Online customer service
Customer service hotline
+86-15504097661 +86-15504097661
Service time:
8:00 - 24:00
Customer service group:
Service Online